2.3–21 GHz broadband and high linearity distributed low noise amplifier

This paper focuses on the design of a 2.3–21 GHz Distributed Low Noise Amplifier (LNA) with low noise figure (NF), high gain (S₂₁), and high linearity (IIP3) for broadband applications. This distributed amplifier (DA) includes S/C/X/Ku/K-band, which makes it very suitable for heterodyne receivers. The proposed DA uses a 0.18 μm GaAs pHEMT process (OMMIC ED02AH) in cascade architecture with lines adaptation and equalization of phase velocity techniques, to absorb their parasitic capacitances into the gate and drain transmission lines in order to achieve wide bandwidth and to enhance gain and linearity. The proposed broadband DA achieved an excellent gain in the flatness of 13.5 ± 0.2 dB, a low noise figure of 3.44 ± 1.12 dB, and a small group delay variation of ±19.721 ps over the range of 2.3–21 GHz. The input and output reflection coefficients S₁₁ and S₂₂ are less than −10 dB. The input compression point (P_1dB) and input third-order intercept point (IIP3) are −1.5 dBm and 11.5 dBm, respectively at 13 GHz. The dissipated power is 282 mW and the core layout size is 2.2 × 0.8 mm².     

隧道洞口上方危岩崩塌块石运动规律及其对隧道的危害

为揭示危岩崩塌块石的运动规律及其对下方隧道洞口的危害,以都香高速昭通段乐红隧道洞口高陡边坡危岩区崩塌体为研究对象,运用理论计算与Rockfall数值计算2种形式对危岩区崩塌体失稳后块石的运动特征进行预测,运用Abaqus有限元软件模拟不同初速度、不同冲击落点下块石冲击隧道结构的动力响应,揭示不同因素对块石冲击隧道结构的影响程度.结果 显示:理论计算与Rockfall数值计算结果吻合,崩塌块石经坠落、碰撞、滚动最终会与隧道引洞段上表面发生碰撞;与冲击落点相比,块石初速度对隧道结构的动力响应特性影响更大;块石冲击落点位于隧道圆拱圆心正上方位置时对隧道结构的损伤最大;不同冲击落点对碰撞回弹后块石的速度影响不大.     

Combustion enhancement and inhibition of hydrogen-doped methane flame by HFC-227ea

Hydrogen enriched with compressed natural gas is an efficient and environment-friendly gaseous fuel. However, the safety issues of mixture and the method to control or weaken their combustion are highly concerned. To explore the inhibition effect of halogenated fire suppressants on the mixture, the effect of HFC-227ea on the laminar premixed methane/air flames, with different fractions of H₂, have been studied. Burning velocities have been measured with constant-volume combustion chamber and kinetically modelled a recently assembled kinetic mechanism. The fractions of H₂ influence the enhancement and inhibition effect of HFC-227ea, and it is less effective with the lean mixture. In stoichiometric condition, HFC-227ea showed good inhibition effect on the mixture flames. The HFC-227ea increased the burning velocities of CH₄-0% H₂-air and CH₄-10% H₂-air flames at leanest condition, whereas the increased burning velocity arising from HFC-227ea not occurred as the addition of H₂ above 20%. Experimental results coincided well with numerical results, however the agreement was poor for the leanest flames at low agent loading. Lastly, kinetic mechanism analysis was used to interpret the combustion enhancement and inhibition effect of hydrogen-doped methane flame by HFC-227ea.     

Aluminium/tin (IV) oxide thermite composite: sensitivities and reaction propagation

ABSTRACT

Thermites are energetic composites made of metal and oxidizer particles that react according to an exothermic reaction and release large amounts of energy. Many possible metal and oxidizer couples exist in the literature. Here, the performance of the aluminum reducing metal and tin (IV) oxide (SnO₂) combination was reported as a function of the fuel/oxidizer mass ratio. The Al/SnO₂ energetic composite, in stoichiometric conditions, was insensitive to impact, sensitive to friction and extremely sensitive to electrostatic discharge. The combustion velocity was determined to be close to 600 m/s. Changing the stoichiometry affected both the sensitivity thresholds to the friction test (160 N to > 360 N) and flame propagation velocity (480–588 m/s) of the Al/SnO₂ composite. These results are reported for the first time.     

球磨过程中介质群运动区域划分方法研究

球磨过程中介质群运动状态变化对物料的破碎效率影响极大，通过对介质群运动状态进行区域划分，探究不同球磨工况下的介质群运动区域特征更能有效揭示介质群对物料的破碎方式和有效破碎区域。针对理论划分介质群运动区域过于理想、单一，试验追踪法成本过高的问题，提出了一种介质群运动区域划分的新方法-EDEM网格划分法。首先把筒体的横截面划分为若干个微元，利用数理统计的方法得到介质群位置概率分布函数，获取介质群运动速度区域分布图和碰撞特性区域分布图。然后给出了回转运动、螺旋运动及复合颤振运动三种工况下介质群运动区域的划分实例，并与试验追踪法对比，验证了EDEM网格划分法的准确性和有效性。最后通过粉磨试验中进料的破碎速率和微细颗粒产率探讨了介质群运动区域特性对颗粒的破碎方式和有效破碎区域的影响效果。本研究为优化球磨过程的影响因素和操作参数提供了一种快捷、有效的方法。     

Computational Investigation of Effects of Grain Size on Ballistic Performance of Copper

Numerical simulations were conducted to compare ballistic performance and penetration mechanism of copper (Cu) with four representative grain sizes. Ballistic limit velocities for coarse-grained (CG) copper (grain size ≈ 90 µm), regular copper (grain size ≈ 30 µm), fine-grained (FG) copper (grain size ≈ 890 nm), and ultrafine-grained (UG) copper (grain size ≈ 200 nm) were determined for the first time through the simulations. It was found that the copper with reduced grain size would offer higher strength and better ductility, and therefore renders improved ballistic performance than the CG and regular copper. High speed impact and penetration behavior of the FG and UG copper was also compared with the CG coppers strengthened by nanotwinned (NT) regions. The comparison results showed the impact and penetration resistance of UG copper is comparable to the CG copper strengthened by NT regions with the minimum twin spacing. Therefore, besides the NT-strengthened copper, the single phase copper with nanoscale grain size could also be a strong candidate material for better ballistic protection. A computational modeling and simulation framework was proposed for this study, in which Johnson–Cook (JC) constitutive model is used to predict the plastic deformation of Cu; the JC damage model is to capture the penetration and fragmentation behavior of Cu; Bao–Wierzbicki (B-W) failure criterion defines the material's failure mechanisms; and temperature increase during this adiabatic penetration process is given by the Taylor–Quinney method.     

考虑速度滑移的多孔质静压气体轴承静特性

对于多孔质材料内的气体流动,基于Darcy定律建立其理论模型,并建立气膜间隙流场的雷诺方程,考虑速度滑移修正方程;将上述2个区域的压力分布方程进行耦合,通过有限元方法对耦合后的压力分布方程进行离散化,用超松弛迭代求解出气膜内各节点的压力分布,分析速度滑移对多孔质静压气体轴承静特性的影响。结果表明,考虑速度滑移所计算的气膜压力分布变化平稳过渡,没有较大的突变。计算轴承的承载力及刚度,结果显示在气密间隙小于15μm时,随着气膜厚度的增大偏心导致的压差增大使承载力不断增大;且当速度滑移系数小于0.1时,速度滑移对轴承承载力及刚度有较大的影响。     

Ultrasonic tomographic velocimeter for visualization of axial flow fields in pipes

An ultrasonic tomographic velocimeter to provide quantitative images of axial flow fields in pipes is developed and presented in this work. To detect the flow in various directions and positions, a novel transducer configuration strategy is proposed. All-in-one transducers are mounted in two sectional planes of the pipe. In each plane, N transducers are equally spaced along the circumference. Overlapped propagation paths are introduced by the configuration strategy, and the influence of the vortex flow can be eliminated theoretically by averaging the line velocities of the overlapped paths. To achieve a fast detection speed, the projection data is collected via an electrical scan in a fan-beam mode. After rearrangement and interpolation of the projection data, the parallel beam filtered back projection (FBP) algorithm is implemented to reconstruct the axial flow field. Numerical simulations with the theoretical velocity profiles were performed. The compensation method for the vortex flow is proved to be effective and necessary, and the number of transducers required for reconstruction of common flow profiles was estimated. Accordingly, an ultrasonic tomographic velocimeter consisting of 2×12 transducers was fabricated. Experiments were conducted in the straight pipe and downstream of a single bend pipe and compared with the computational fluid dynamics (CFD) simulation results. As demonstrated, the ultrasonic tomographic velocimeter was capable of visualizing both symmetric and asymmetric axial flow fields with high reliability.     

Spatial filtering velocimeter using frequency shifting by the method of rotating kernel

A new approach of frequency shifting by rotating kernel is proposed to improve the performance of a spatial filtering velocimeter, used to provide accurate velocity information for a vehicle self-contained navigation system. A linear CMOS image sensor was employed both as a spatiotemporal differential spatial filter and as a photodetector. The filtering operation was fully performed in FPGA and is realized by applying a rotating kernel to the pixel values of the image. Theoretical analysis showed this method could double the maximum measurable velocity. The power spectrum of the output signal was obtained by fast Fourier transform (FFT), and was corrected by a frequency spectrum correction algorithm, named energy centrobaric correction. This velocimeter was used to measure the moving velocities of a conveyor belt. Experimental results verified the method’s ability of reducing the output signal frequency and standard uncertainty of velocity measurement. What is more, the undesired output introduced by frequency shifting to the power spectrum of the output signal was deeply investigated and a new method was proposed to eliminate the undesired component in output signals. This velocimeter aims at providing accurate velocity information for vehicle autonomous navigation system.     

Output feedback tracking control for rigid body attitude via immersion and invariance angular velocity observers

A novel immersion and invariance (I&I) angular velocity observer is presented for the attitude tracking control of a rigid body with the lack of angular rate. Global exponential convergence of angular velocity estimate errors are guaranteed by an innovative filter design for the estimates' Euclidean norm. The proposed method requires fewer filter states compared with existing I&I angular velocity observer designs, which achieves a simpler closed-loop structure (dynamic reduction). The observer synthesis and convergence are independent of the control torque, which leads to much convenience in establishing “separation property” when combining a proportional-derivative attitude tracking controller driven by angular velocity estimates. A rigorous stability analysis is provided to ensure the (almost) global asymptotic convergence of the overall closed-loop tracking errors, and several numerical simulations are carried out to demonstrate the effectiveness of the combined implementation of proposed angular velocity observer and full-state feedback attitude tracking controller.